ENERGY IS
THE KEY TO CIVILIZATION- don't believe me-
go live just one day in the woods- the
valuable resource is getting dry as India
and china want to live a little like the
west-cant blame them- who I do blame is
being on this net for so long as everyone
uses their own arrogance and negativity to
ignore solutions for energy- how many people
have you met in your life that says they
solved it- go ahead and ignore this as the
rest in past year- when the total economy
fails- don't be puzzled as you did nothing-
pressure a university to investigate and
repeat- I don't want your money-take your
energy and help solve the energy crisis
Viewing the video, the author needs to be
congratulated for putting his ideas into
practice. His technique is to discharge a
high voltage (tunable) high frequency Tesla
coil into a water bath, which may have some
components of heavy water. In the video and
comments he mentions putting 6000 watts into
the water. Further, he notes that the Tesla
coil itself gives off Gamma bursts, so that
those measured could not be ascribed
directly to the fusion process.
I did see no mention of measurement of
high energy neutrons (admittedly which is a
very difficult thing to measure). The
requirement of 750 KV is mentioned often. Is
that the potential needed for acceleration
of the hydrogen to produce fusion?
The system could certainly be downsized
to experiment with. What frequency is being
used to resonate in the water? There are
other, more stable power systems rather than
Tesla coils, which produce a very clean high
voltage, high frequency waveform, but with
very little amperage. More significantly,
such sources would not have Gamma ray
emission, so that any detected rays would
necessarily come from the fusion process
itself.
In the Azar Fusion model, a Tesla coil
discharging between two electrodes in water
creates a plasma state following
dissociation of the water to hydrogen and
oxygen. The intense electric field causes an
acceleration of the hydrogen ions toward the
negative electrode, at a velocity that may
reach relativistic speeds. As any
accelerating charged body also emits a
magnetic field, so too does the moving
proton. The field so generated is akin to
that of the magnetic field around a current
carrying wire: the magnetic vector is
strictly angular, whose magnitude decreases
as the inverse square of the distance
between the test point and the moving
proton. If there is another moving proton
nearby with the same vector direction as the
first moving proton, then this magnetic
field will give rise to a force on the
second proton that is directed radially
inward to the first proton. A bunching up of
the parallel protons, or "squeeze" will
occur. These equations and effects are fully
described in the inventors "scientific"
disclosure.
The inventor makes the leap that the
subsequent radial velocity caused by this
magnetic bunching effect is sufficient to
overcome the natural Coulombic repulsion
between these two protons, so much so that
fusion will occur. For proton fusion, a
velocity equivalent to 200-300 million
degrees Kelvin is necessary IN THE RADIAL
DIRECTION BETWEEN THE FUSION PROTONS. For
deuterium fusion, only 20-30 million degrees
Kelvin equivalent velocity. The Telsa coil
pulse provides a longitudenal acceleration
of the protons; it is the magnetic pinch
effect that provides the radial
acceleration. Thus, simply increasing the
intensity of the Tesla coil may achieve a
change in longitudenal velocity from .95 to
.98 of the speed of light, but the
corresponding radial net velocity would not
be anywhere near that amount.
It is possible, however, for fusion to
occur in isolated regions of the wave
pathway between the two electrodes, as an
accelerated proton in split water may impact
a water molecule just before it has been
split; in this case the enormous velocity
imparted to the proton may be sufficient to
overcome the Coulombic barrier. However,
this is not a magnetic pinch effect, but it
may give rise to some low level evidence of
fusion occurring. In this case, one should
do an energy balance to see if the net
process is economically profitable (i.e.
muon based fusion is possible, but not
profitable).
The major problem with the Farnsworth
Fusor is instability. The Fusor, when
operated at fusion levels, with give rise to
jets of ions which escape the spherical
confining field. Thus, the Fusor fusion is
possible, but not profitable. Perhaps this
inventor can combine the two technologies,
and utilize the magnetic pinch effect to
bring stability to the fusion process, thus
making the device possible and profitable.
That is, utilize a deuterium water source,
use a tunable Tesla coil to energize two
electrodes, both electrodes set at the
output potential of the coil, and surround
the electrodes with a grounded open type
electrical wire sphere. The AC oscillation
induced by the Telsa coil may be sufficient
to create stability so that ion jets do not
form. Just a suggestion.
I will admit that the calculations behind
the physics are over my head but I
understand magnetic fields, fields of
energy, and how it is necessary to smash
particles together to capture nuclear
energy.
A plasmoid is a stabilized ball of plasma
which is contained within its own magnetic
field. Chukanov discovered this and along
with his work in cold fusion has grasped the
concept.
The Bussard Polywell device with
concentric magnetic fields is a way to
manipulate the flow of the plasma to get the
necessary reaction. It was adapted from the
Farnsworth–Hirsch Fusor.
After much experience reviewing plasma
systems and every type of fusion reactor
known to the wiki world and after reviewing
the noble fuse technology I have come to a
conclusion.
The concepts behind the Azar Fusion
device are sound. Sandia National Labs
achieved temperatures in excess of 2 billion
degrees kelvin which is hot enough to
achieve aneutronic fusion of Boron 11. For
Mr. Azar to achieve the temperatures and the
necessary velocity in order for fusion to
occure with hydrogen or deuterium is very
much conceivable. 100 to 300 million degrees
kelvin in this device seems possible.
Last month you asked me to review a
magnetohydrodynamic ocean generator which
used the water as the containment field for
a solid state magnet generator. Mr. Azar has
applied the same principle to his technology
utilizing the water to contain the magnetic
field. Within this magnetic field
electricity is passing at a high speed and
the ionized particles get caught in the
plasma pinch.
The concept for using a toroid to give
increased efficiency is one that is applied
in most fusion reactors to date.
The potential for scaleability, the
simplicity and reproducability of the Noble
Fusion technology gives this system merit
when it comes to the development of viable
free energy devices.
There are novel concepts with water based
fusion reactors when it comes to containment
and replenishing fuel. I believe that there
is the potential for atmospheric pressure
devices and much development that may stem
from this technology. My first suggestion
would be to employ the concept of the
Farnsworth Hirsch Fusor in a heavy water
based reaction vessel.
If the technology can be validated it
will open the doors to the development of
optimized devices. I have many
recommendations for alternate configurations
in mind but I wil save those for another
day.
Hello, my name
is Solomon Azar- I HAVE FOUND
THE ROAD TO SAFE CLEAN NUCLEAR FUSION- When
this is found and understood- the energy
crisis will end- I have been looking at this
system since 2002 and it is perfect in every
way. I finished my experiments April-2007. I
have since that time tried to the best of my
abilities to inform many people upon the
net- there is no question It would be nice
if concerned citizens would offer
suggestions or help provoke a university to
simply repeat my experiment to end the
energy crisis--
maybe after this next global nuclear war
OVER ENERGY will people learn the lesson-
when presented with solutions in life
FREELY- CHASE THEM.
I have performed an
experiment never done before in science- I
used a Tesla coil for its use in high
voltage high frequency and apply its
discharge plasma not upon the dielectric of
free air- but to the dielectric of water
itself- specifically I used ultrapure
reagent grade water from manufacture
NERL-this is to establish the high degree of
insulation needed for plasma (you cannot
have contaminants for conductivity)- I doped
my water with heavy water from the
manufacturer UNITED NUCLEAR-(however- a full
concentration of heavy water is desired)- I
built my 1 million volt Tesla coil entire
tunable- every aspect of it- as it must be
done to TUNE THE OUTPUT DISCHARGE OF THE
TESLA COIL to the water itself- once the arc
is stable- the voltage may be increased- I
have written in my pdf file in my website of
noblefuse.com that a prerequisite of 750 kv
is needed as an electric field gradient
about the charged particles used in fusion(
in this case the hydrogen bound in the water
molecule) because of voltage drops as
expected as in all electrical systems upon
the load (load here is the water)- a much
higher voltage is needed in order to
distribute the voltage gradient upon entire
arc plasma length between electrodes in
water-
Power reactor in which the
heat is dissipated from the core using
highly pressurized water (about 160 bar) to
achieve a high temperature and avoid boiling
within the core. The cooling water transfers
its heat to the secondary system in a steam
generator. Example: Grohnde Nuclear Power
Plant in Germany with an electrical output
of 1,430 MW.
Replace the rod assemblies
and use electrodes to conduct the Lightning
bolt! High Voltage High frequency will
create the magnetic pinch to slam the
isotopes of hydrogen together which is bound
in water- helium and oxygen are the
outgassed products recaptured by expansion
tanks-it is absolutely perfect!
_ I HAVE FOUND THE TRUE PURPOSE OF THE TESLA
COIL- the answer was always in the lightning
bolt- understanding of gamma bursts from
lightning discharges have only been recently
vindicated from satellite in late 90s---
CA 94305 United States
Said, R ( ) , STAR Lab, Electrical
Engineering, 350 Serra Mall, Stanford, CA
94305 United States
Smith, D M ( ) , Physics Department and
Santa Cruz Institute for Particle Physics,
University of California, Santa Cruz, 1156
High Street, Santa Cruz, CA 95064 United
States
Lopez, L I ( ) , Astronomy Department and
Space Sciences Laboratory, University of
California, Berkeley, CA 94720 United States
The observation of brief (<1 ms) bursts of
intense γ-rays, the so-called Terrestrial
Gamma-ray Flashes (TGFs), by the BATSE
γ-ray experiment was one of the most
unexpected discoveries by the Compton
Gamma-Ray Observatory.
Let me try to give another analogy to make
the point. think about striking a match, if
all conditions are proper , one knows that
to strike a match, you must go a minimum
speed- you cannot strike the match too
slowly- this is understood as more speed is
more friction and thus more activation
energy necessary to create combustion of the
match material. the same applies to this
fusion system, first, imagine my system as
inside a pressurized water reactor used in
fission plants- the moderator is already
heavy water- we shall use it as the fuel. I
have said the plasma arc looks exactly like
our friend the electric lightning bolt- but
I talk about in my pdf file- that the so
called lightning bolt must be understood in
regards to high voltage and frequency- just
like the minimum speed needed for the match-
so it is with the combination on high
voltage and frequency to not only resonate
with the dielectric molecule of heavy water-
but more so- to create a minimum velocity
upon charged particles in the fuel water.
this velocity is also exhibiting itself as a
magnetic field-think of the cathode ray
scope- in a snap shot instant in time for
analysis, look at when the maximum energy is
being applied on a per strike basis of the
input cycle- or shall we say the highest
amplitude of the ac signal. if for example-
an input energy of one megawatt was injected
into the strike of the arc- a magnetic pinch
shall be directed upon the charged particles
in transit of the discharge- in a
thermodynamic extraction process such as
this - we need at least 5 times more energy
out of the system to recoup our initial
energy input- and a surplus for commercial
energy supply- thus- via fusion of hydrogen
to helium- with each strike- a minimum
voltage and frequency SHALL give the minimum
activation energy required for magnetic
pinching and fusion of the isotopes of
hydrogen. to increase the q of the reaction
in this system- a magnetic toroid may be
used around the plasma arc for increased
efficiency= such as used in tokamak devices.
I hope this analogy helps those who question
this system- THANK YOU--
Here is a thought experiment for
electromagnetic fusion with Einstein in mind
Pretend
you are water-you are an oxygen atom- you
are stable- you are noble- 8 protons-8
neutrons-and 8 electrons- there are only 5
magic shell nuclear elements of the periodic
table- oxygen is one of them- it is very
stable-
Therefore- you are stable and noble- you
have no need for fusion- yet it could
happen- but the probability of another
element such as hydrogen and its isotopes
would be made to fuse together in some kind
of fashion mankind tries will occur way
before oxygen does- - ok-so now you are this
noble one and you have outstretched in your
hands a hydrogen atom and or its isotope
deuteron and you hold it out to mankind as a
gift-
Man
understands the gift of fusion for many
years and is desperately trying to do such-
I
propose electromagnetic fusion- I propose
the BENNET pinch used in poloidal currents
used in plasmas of tokomaks- but much
further-
Here we
go – the thought experiment- you are this
oxygen atom with two hydrogen’s and you
stand amongst your friends similar in
nature. You are placed in a large vessel
filled of your kind-now imagine that two
walls opposing in this vessel are the plates
of a capacitor- who cares what is applied to
the capacitor plates (electrodes of
system)-for all you know as a noble oxygen
and the hydrogen you have in your hands is
nothing more than the electric field upon
the plates-
You are
composed of charged particles- thus you will
interact with the applied electric field of
the plates-this is common electronics and
electric knowledge-
However,
I speak of dielectric breakdown- I speak of
the lightning bolt- let us now assume we
have made the capacitor plates oscillate at
1 million volts peak to peak as way of a
tesla coil
Think of
the electric field- everything will be
controlled by this field- a dielectric
breakdown will occur- and all discharge
current will begin to flow and oscillate as
a function of the applied voltage-
Now- you
are in the heart of a lightning bolt- you
who are noble as a oxygen probably lost all
your valence electrons due to the magnitude
of such a high electric field- every charged
particle in transit of the discharge current
is surely ionized and talks of being a
complete water molecule should be erased-
the state of this plasma current is nothing
more than ionized hydrogen and oxygen and a
complete sea of electrons-
Let us
think first of the electrons- 1896 times
smaller than protons- no question it will
oscillate much faster as a function to the
applied voltage- remember the cathode ray
scope- basic physics also will say this
charged particle will also have a magnetic
field about itself because of the electric
field that has driven it-thus- this
oscillating electron current will have an
intrinsic magnetic field
Let us
now think of the protons- oxygen has 8 and
surrounded by 8 neutrons and is far less
likely for reaction than isotopes of
hydrogen for fusion- this should merely be
understood by refereeing to atomic tables of
elements and known theory- but this hydrogen
is a singly bound proton with mass one-
unless we speak of a deuteron- it will also
be controlled exactly the same way as the
electron is affected by the external applied
voltage- however- it is opposite to the
electrons motion-and much slower by its mass
– however-its magnetic field will add to
that of the electrons- this is standard
knowledge of magnetic field generation of
charged particles by way of electric fields-
Thus, in
this thought experiment- within this state
of dielectric breakdown- I like to say the
lightning bolt- can you now see the
oscillation of the charged particles by such
a large magnitude of the applied voltage
plates- can you now see the probability at a
certain moment in time- particularly when
the applied ac signal is greatest- that all
magnetic fields of charged particles in
transit can have the power to be
magnetically pinched-
Magnetics have push and pull- it is well
known that high frequency causes a
constriction upon electrical currents-
whether in copper lines and forcing such to
the surface- or in plasma and made use to
constrict it - high frequency is known
to constrict the currents- thus- do you see
the forces I am referring to as this
dielectric breakdown has occurred upon the
most perfect fuel of the heavens- water-
this oxygen atom holds the hydrogen for us-
we shall apply a high voltage (high is
relative- I have stated 750kv in the
vicinity of the hydrogen for fusion- I come
to this by way of understanding the beta
decay of a free neutron- if it can
disintegrate- it can come together- made
into a deuteron- then made into helium)-
Thus –we
make helium and oxygen is then unbound and
must also be recaptured- this is easy in
expansion tanks- the byproducts are helium
and oxygen-truly noble-
To
increase the q of this system- a simple
toroidal magnet as used in tokamaks for
plasma control may be used for additional
pinching-
I hope
this helps- however- you must always think
of the applied electric field and its
magnetic inducement upon the charged
particles- we will stably run the Tesla coil
upon the dielectric of water itself (more
appropriately heavy water) and turn up the
voltage for greater acceleration speeds and
thus magnetic fields- we can control
pressure in this vessel- we can control
electrode spacing and so much more-
that is
my thought experiment for you to understand
it is my intention to use all input energy
by way of oscillating a very large electric
field which will induce the proper magnetic
flux density in units of Tesla for a
pinching- not established hot fusion whereby
all energy input is chaotic and the
probability of fusion comes by way of
statistics from a gas equation- no- high
voltage and high frequency in an orderly
manner by the construction of a man made
lightning bolt with controllable parameters
inside an existing pressurized nuclear
reactor- everything is off the shelf-
the world will run on steam power again
globally-from trains-factories-ships-and all
power plants- I offer the Watt steam engine
again- not with two sticks to make fire and
boil the water- but electromagnetic fusion
with two electrodes to induce fusion of
hydrogen isotopes to boil water and make
steam- it is absolutely perfect.
To the
CEO's of nuclear power plants-or pressurized
coal fired- you have spare reactors in the
back yards of your plants- take a 1 million
volt tesla coil and do what I have said- you
will measure its fusion reactions and you
will conclude this - I have found the road
to safe clean energy.
I speak
plain science- please connect the dots and
let us end this energy crisis for a world
that desperately needs energy- May the light
of God shine upon all our actions for the
betterment of mankind
Solomon
Sami Azar
update-after
33 months on this net- it seems evident
people do not care until the machine breaks,
right before our eyes our economy collapses
as inflation and energy costs have been
eating at our economy for some time now-
maybe even global war with russia and iran
will you finally care to investigate. Time will tell.
Nov 13- 2009
Not two sticks- But two
electrodes
my system will in
time be viewed as simple as two sticks to
make fire as early man, Fire from water with
two electrodes in the 21st century will take
mankind to a bright and prosperous future as
we progress together
not two sticks but two electrodes This
is a picture of the very first transistor-
it looks nothing like a real production
transistor- but principle applies--what I
have demonstrated with a Tesla coil of high
voltage high frequency and have written in
PDF- should be clear to the trained eye-
that I- Solomon Azar- Have invented the
first practical fusion generator system
The following youtube video is a very
large tesla coil- imagine the concentrated
arc discharge between electrodes inside a
pressurized water reactor such as a nuclear
fission power plant. the moderator is heavy
water!!! WE SHALL USE IT AS THE FUEL. TO
INCREASE THE EFFICIENCY OF THE OUTPUT FUSION
REACTIONS. AN ADDITIONAL MAGNETIC FIELD IS
APPLIED ABOUT THE ARC DISCHARGE- WE MAY USE
TOROIDS AS USED IN TOKAMAK FUSION REACTORS
TO INCREASE THE MAGNETIC PINCH WITHIN THE
ARC DISCHARGE. SIDE NOTE- MAGNETIC FLUX
DENSITY IS MEASURED IN TESLA!!!!! "THIS
INVENTION WITH A TESLA COIL WAS MEANT
TO BE"
THEY ACTUALLY STUCK 43 CANDLES PLUS ONE-
COULD HAVE MADE HOT DOGS UPON THAT FIRE
- GOD BLESS EVERYONE
I
fundamentally believe I have solved the
energy crisis. this is a very hard state of
mind to be in possession of when you hear a
world crying for energy solutions and
greenhouse gases. - I concluded my tests on
palm sunday-april-2007- However, knew it
would work since late 2002- I tried to relay
this openly since then such as several
at los alomos laboratories and sandia labs-
they like it-but too speculative and they
are too invested in something else- so I
continue upon my own efforts and just build
it-
I have been trying to ask the public to
spread this discovery so many will see it-
for out of many a few select will
understand- I have tried every possible
angle to spread this- even religious to no
avail- I have tried some fusion journals-
but my system is completely new and not
understood- I am the first human being to do
this- thus- it will take time for the next
and so forth- The day you have a positive
frame of mind- you will understand this
process- look at the stable plasma arc
within the heavy water itself contained by
all parameters in a pressurized vessel- my
video is real- not fancy graphics- if I
alone with junkyard parts can do this- what
can a nuclear power plant and staff do with
a spare reactor in their backyard? clean
nuclear safe fusion right here- I dare you
to prove me wrong- but it would be nice if
you prove me right :)
- I am bewildered as to how many don't care-
ENERGY IS THE KEY TO
CIVILAZATION_PERIOD___will you do something
about this? or must the global economy be
destroyed before you care.
june 13-2008
if you want to save the world
from global war and economic collapse from
energy - email princeton plasma labs and
force them to repeat my experiment as they
are too arrogant to listen to the deed of an
outsider- when my system proves true to save
the world of greenhouse gases and clean
energy for all nations- you will say- THANK
GOD--http://www.pppl.gov/-
or the American energy department-http://www.ne.doe.gov/
This
is a picture of the very first transistor-
it looks nothing like a real production
transistor- but principle applies--what I
have demonstrated with a Tesla coil of high
voltage high frequency and have written in
PDF- should be clear to the trained eye-
that I- Solomon Azar- Have invented the
first practical fusion generator system
- GOD BLESS EVERYONE
